Exclusive Products
Digital (Manual / Semi-Automatic / Automatic Reset) Electronic Overload Asymmetry Relay Thermal Relay TRM 25 150-260VAC
General This overload devices are designed to prevent the loads getting harm from over currents and ability of control at the same time.TRM-03, TRM-12 and TRM-25 are have internal current tansformers.Usage of Device and Working Principle Make the connection of the device according to the connection diagram. Energize the device after making the connections. The display shows the set values for 5 seconds when the devices is energized.When the device is energized, you can make a overload adjustment with the "A>" knob While the setting is being made, the set value is shown on the left display. You can set the delay time with the "t" knob. Wtrine the setting is being made, the set value is shown on the left display. When th device is energized, the relay is energised, the contact output goes to terminal 3 and "OUT" led is on If the currents is higher than the set high current (A>), the device is counts the delay time and ERR on. After the time has elapsed, the relay is de-energised, the contact output goes to terminal 1, and "OUT" led is goes out. Delay time (Start Current): After the relay is energized or reset, the device does not current control for 5 seconds. Allows to delay time. Asymmetry: If there is more than 50% difference between the highest and lowest current passing on the phases, the device will enter asymmetry fault within 2 seconds. (When the motor starts, if a phase loss occurs, the motor can be prevented from being damaged.) When the device enters the asymmetry error, the display group of the two phases causing the fault flashes and error LED is on. If the current is less than these values, the device does not control asymmetry. 0,1A for TRM-03, 1A for TRM-12 and 2A for TRM-25. The device must be manually "Reset" button or power off to exit asymmetric errors.Reset ModesNote: Press the SELECT button for 10 seconds to change the mode. The mode light will change.WarningsWarnings - Please use the device according to the manual. - Don't use the device in wet. - Include a switch and circuit breaker in the assembly. - Put the switch and circuit breaker nearby the device, operateycan reach easily. - Mark the switch and circuit breaker as releasing connection for device. - Maximum currents to be applied to the devices; 3A for TRM-03, 12A for TRM-12 and 25A for TRN If current is applied above these values, the device may make incorrect measurement or damage echnical .Maintenance Switch off the device and release from connections. Clean the connection point of device with a swab. Don't use any conductor or chemical might damage the device. Make sure device works after cleaningTechnical SpecificationsOperating Voltage....... : 150V-260VAC Operating Freq.............: 50/60Hz Operating Power...........:
INGCO 9pcs Insulated Hand Tool Set HKTV01H091
Specifications:1 8 '' insulated combination clamps1 x 6 '' insulated diagonal cutters1 x 8 '' insulated long nose pliers1 ph1x80mm insulation screwdriver1 PH2x100mm insulation screwdriver1 SL4.0x100mm insulation screwdriver1 SL5.5x125mm insulation screwdriver1 PH0x60mm insulation screwdriver1 Pcs test pencil (Test voltage : 100-500VAC)Packed in a stackable plastic box
FLUKE 2AC Sensor Non-contact Voltage Detector AC tester Stick electrical Detector Pen
Fluke 1 VoltAlert Non-Contact ACV Detector 200-1000V.The next new generation VoltAlert AC non-contact voltage testers from Fluke are easy to use - just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there¡¯s voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home.Features:Voltbeat technology and continuous self-test- so you always know it's workingUpon detection, tip glows and beeper soundsCAT IV 1000 V for added protectionRange: 200 V to 1000 V AC
Solar Light Motion Sensor Security Dummy Camera Wireless Outdoor Flood Light IP65 Waterproof 77 LED Lamp 3 Mode for Home Garden
Solar Light Motion Sensor Security Dummy Camera Wireless Outdoor Flood Light IP65 Waterproof 77 LED Lamp 3 Mode for Home GardenFeatures:▪【2 in 1 Solar Light & Security Dummy Camera】 - Keep your home property safe and intruders away. With 77 Bright LEDs, motion-activated, sleek Low profile design. Plus realistic dummy security camera. Detect Intruders Stay away from your household▪【3 Lighting Mode Optional 】- ① Light off at night, just red light flashing, strong light mode on when motion detected;② Weak light mode at night, strong light mode on when motion detected;③ always light on mode ,red light is always flashing on any mode▪【Long Time Working with battery】 - The security light with 2400mAh battery can offers up to 8 hours using time , additional solar panel for wire-free easy installation and absorbs solar energy under sunlight, environmental and power saving▪【Built-in PIR motion sensor】- The light will be automatically triggered when motion is detected at the distance of 10ft - 30ft, range of 120 degrees in the night. Perfect for garden yard lawn patio garage porch driveway landscape security. Make your life more convenient▪【Adjustable and easy to install】- The solar light is pretty easy to be installed. And the rotation can adjust the optimal illumination angle and solar panel angle with easy, IP65 waterproof perfect for outdoor useSpecification:--battery:18650 2400mah lithium battery--77led/2835 SMD white light+1 led red light--solar panel:5.5v/300mAh--material:ABS--waterproof:IP65
FLUKE 302+ Handheld Digital Clamp Multimeter Meter Tester DMM AC/DC F302 PLUS Clamp Meter
Product overview:The Fluke 300 series compact AC clamp meter is easy to use and can meet the needs of daily basic electrical maintenance. It has the following characteristics: AC current 400A, which can meet the needs of customers with different applications; the new body design allows Fluke 300 AC clamp The watch is more compact and beautiful, which meets the market's requirements for product size, appearance and feel.Main features1. Brand-new body design, Fluke 302+/303/305 AC clamp meter is more compact and beautiful, which meets the market's requirements for product size, appearance and feel, making the use of clamp ammeter more flexible and simple;2. AC current 400A (302+), 600A (303), 999.9A (305), can meet customers with different application requirements;3. 30mm large jaws;4. Meet the high safety level of CAT IV 300V/CAT ||| 600V;5. High accuracy of 1.8% (1.5% for 305);6. All series of AC clamp meters have backlightfunction;
D-link dsl-2750 wireless router
Item details:Brand Name:D-LinkWith Modem Function:YesType:wirelessWired transfer rate: 10/100 MbpsWAN Ports:OtherNumber of USB interfaces: NoneFrequency supported by Wi-Fi:2.4G5G Wi-Fi Transmission Rate: NoneModel Number:DSL-2750UStandards and protocols:Wi-Fi 802.11n2.4G Wi-Fi transmission rate: 300MbpsLAN Ports:4Support WPS:YesFunction:VPNBrand:D-LINKModel:DSL-2750UPart Manufacturer:DSL-2750U/R1AType:Wireless RouterInput interface: ADSLExternal antenna:2.Antenna type:External removableRange 2.4 GHz:YesNumber ranges:Single BandNumber of output ports 10/100BASE-TX:4Number of antennas:2.Support Dynamic DNS:YesSupport WPS:YesStandard WEP:YesWPA-Standard:YesStandard WPA2:Yes
Universal Power Adapter Supply Charger adaptor 12V 3A Eu for LED light strips
· Certification: RoHS · Origin: CN(Origin)· Model Number: Power Adapter· Output Interface: 5.5mm*2.5mm· Usage: Switching· Output Type: DC· is_customized: Yes· Connection: Plug In· voltage: 12V· current: 3A· Polarity: Internal positive, External negative· Applications 1: Router, Speaker, CCTV camera system, LED strips
Digital Meat Thermometer TP101
PRODUCT SPECIFICS:Model: TP101 electronic digital food thermometerThe probe is made of stainless steelWeight: 0.039kgProduct list: a thermometer, a manualMeasuring range: water temperature, food, liquid, paste, oil temperature, milk temperature, tea, soup, beer and so onTemperature measurement range: -50 ° C to 300 ° C (-58 ° F to + 572 ° F) Wide range of measurementFeatures:Pen-type structure, stainless steel probe, straight measurement, easy to carry.Button function Description: 1, ON / OFF: switch function2, C / F: Celsius / Fahrenheit conversion3, HOLD: temperature lock function, press this button, then the temperature is locked, and then press the lock function to lift.4, MAX / MIN: high temperature and low temperature memory, press this button to display the previous high temperature, then press the previous display of low temperature, and then restore the temperature measurement state.Technical data:Resolution: 0.1 °Accuracy: ± 1 ° (-20 ° ~ +80 °) ± 2 ° (other range)Power saving mode: 10 minutes automatic shutdown power saving functionPower supply: AG13 button battery 1(not including)Please specify your choosing color,if not,we will send color randomly(black and white)
Micro SD TF card for xiaomi phone 128gb
XIAOMI Micro Flash Memory Card Card 128GB Micro Class 10 High Speed Micro TF CardDescription:Characteristic:1. Capacity: 128GB2. Micro sd card adapter3. Plug and play (no software required)4. Micro TF format, high speed reading and writing5. Suitable for mobile phones, cameras, MP3/MP4 players and other devices6. Can be used as Micro or sd card7. Operating temperature -13°F to 185°F (-25°C to 85°C)8. Storage temperature -40°F to 185°F (-40°C to 85°C)9. Dimensions: 0.59x0.043x0.03 (14.99x10.92x1.02mm)Specifications:* New improved version* All sealed in retail packaging (not bulk packaging)* Take top quality photos and shoot full HD video* Capacity is up to 16GB, which can be photographed, carried and completely recorded* 10 level video rating for full HD video capture* Play app performance faster to capture better photos* Take top quality photos and shoot full HD videoPackage Contains:1* micro card1 * SD card adapterNotes:Please do not use cheap card readers to test Micro cards, the fast
UNI-T UT58A digital multimeter
The UT58 series is a safe and reliable, easy-to-use hand-range digital multimeter. Its large 60mm x 54mm LCD screen conveniently displays measurement results. This series digital multimeter satisfies a variety of applications in electronic and electrical fields.Features:1. Display count of 2000, refresh rate 2~3 times/s2. Function symbols and test lead connection indication3. Transistor measurement4. Continuity diode and buzzer; Auto power off; overload protection5. Data maintenance; 20A AC/DC current measurement
MT8206 Upgraded Digital Oscilloscope Multimeter 2 in 1
Package Included:1 x MT8206 Unit1 x Bag1 x Pair of Probes1 x Operator’s Manual1 x Package BoxComparison:MT8205MT8206Max Display1999● 3999ScreenOrdinary● HD display Screen; White on black; large view angleBandwidthAC 10KHZ● ACA/ACV/DCA/DCV 20KHZMeasuring RangeManual range● Manual/auto rangeAnalog Bar GraphNo● YesStorage Capacity100 datas, 5 waveforms● 100 datas, 10 waveformsCapacitance200μF● 0.1μF-100μF/10mFFrequency2KHZ-200KHZ●5HZ-5MHZResistance20MΩ● 40MΩOverview:MUSTOOL MT8206 emphasis on functional combination for field testing process, not to replace the meter. It reflects the high-tech, using a dedicated chip has, as wave function, you can view the waveform signal 20KHz within. As a large number of measuring instruments waveform, you will find MT8206 is the most affordable one, spend the price of a multimeter, you can have a table can be seen, as the waves of the waveform, value for money!Features:1.Analog Bandwidth : ACV/DCV/ACA/DCA 20kHz , 200k high-speed A/D sampling2.HD Display Screen3.Digital multimeter with 41-segment analog bar display,200k high-speed A/D sampling,4000 counts auto-range(can be selected manually), one-button switch of graphical waveform display during measurement4.High reliability with panel calibration technology and memory calibration, sparing the need for adjustment with potentiometer5.Storing 100 sets of data and 10 waveforms independently6.Capable of holding waveform and data during measurement,easy to view and analyze7.Realizing one-button automatic waveform-capture,operator-friendly to learn and operate8.Displaying historical data and real-time measurement on the same screen with unique records reading mode for easy comparison9.Effectively eliminating lead resistance, distributed capacitance or interference signals with relative value measurement (clearing)10.Extending battery life with automatic shutdown function11.Featuring DC/AC voltage/current, resistance,capacitance/mF (large capacitance)12.Frequency/ cycle, diode/continuity test13.Frequency measurement with 5Hz ~ 5MHz automatic switching range and the maximum input of 380VAC14.10A AC and DC current measurement with protection against voltage error15.Capacitance double gear design 0.1nf-100uf gear position: convenient for small capacitors to measure quickly16.10mf gear position: high capacitance and high accuracy are guaranteed.
miter shears 45 to 120 degree PVC trunking and steel sheet cutting
PVC Trunking Chamfer Cutter, Fillet Cutter, Miter Shears, Multi-Angle Steel Trim, Siding, 45-120 Heavy Duty Cutting ToolsFeatures :-High quality blade-Fully replaceable parts-Worn blade can be replaced.- With corner device for convenient use-Designed for use on timber and plastic formwork netting.-Designed to cut trunking, article plastic, lath, plastic pipe or any plastic products;-It can also cut the trunk (branch) in any angle, tires, lead, wire and copper bar, etc.-To complete all kinds of arbitrary shear: 45°,60°,75°,90°,105°,120°.- Able to adjust the angle from 45° to 135° left and right if you need.-The angle device is easy to break, does not cut steel-Caution: do not place your hands near the blades.Specifications:Mode:311AMaterial: steel + plasticSize: 220*22mmPackage Included :1 x shear/in a package
Repair tools flexible shaft extension with accessories BKGJ-001-L
Repair tools flexible shaft extension with accessories BKGJ-001-LName: Ratchet Screwdriver Combination Kit-Two-way rotation, free conversion,- Alloy steel tool shank, good torsion hardness.-The batch head is made of chrome-vanadium steel with high hardness.-Package includes:1 Piece Lengthening RodSet of screws 10 pieces:3 Flat Screwdriver Heads: 4-5-62 cruciform heads +: PH0, PH12 cruciform heads *: PZ1, PZ22 TORX head (star): T15, T201 AD Hexagonal head
FLUKE 302+ Handheld Digital Clamp Multimeter Meter Tester DMM AC/DC F302 PLUS Clamp Meter
Product overview:The Fluke 300 series compact AC clamp meter is easy to use and can meet the needs of daily basic electrical maintenance. It has the following characteristics: AC current 400A, which can meet the needs of customers with different applications; the new body design allows Fluke 300 AC clamp The watch is more compact and beautiful, which meets the market's requirements for product size, appearance and feel.Main features1. Brand-new body design, Fluke 302+/303/305 AC clamp meter is more compact and beautiful, which meets the market's requirements for product size, appearance and feel, making the use of clamp ammeter more flexible and simple;2. AC current 400A (302+), 600A (303), 999.9A (305), can meet customers with different application requirements;3. 30mm large jaws;4. Meet the high safety level of CAT IV 300V/CAT ||| 600V;5. High accuracy of 1.8% (1.5% for 305);6. All series of AC clamp meters have backlightfunction;
Phase relay with display ENERGICAL RDP1. 380V
Phase relay with display ENERGICAL RDP1. 380VDescription :The phase relay provides protection against phase faults:It signals high voltage, low voltage, lack of phase, asymmetry and phase inversionFurther information :Weight: 0.13kgDimensions: 9.5 × 7.5 × 4.3cmCurrent (A): 8Frequency (HZ): 50/60Voltage (V): 380.
DC Male Power Connector
DC Male Power ConnectorrSize:Inner diameter: 2.1mmOuter diameter: 5.5mmTransmission voltage: 5V-38VTransmitting power: 80WUsed for: led strip, CCTV camera, power supply, 3D printerCharacteristic:The wire core is thick and can withstand voltage from 12V to 36V,The outer skin is made of plastic and other materials, and the wire body is softHigh fidelity design, good power transmission effect
TENSE ERS-07 Right-Left Timer (Inverser)
TENSE ERS-07 Right-Left Timer (Inverser)DESCRIPTION:Time relays are designed for use in all areas requiring time dependent control. Operation: 1sec. - 100min. (adjustable)Wait: 1sec. - 100min. (adjustable)CHARACTERISTIC:Function: multifunctionMounting: DIN rail, for panel mountingProduct applications: for DIN railOther features: adjustable
SONOFF nspanel Pro connected home control panel
SONOFF NSPanel Pro Smart Home Control Panel EU HMI TFT 3.95" Touch Screen Smart Scene Display Voice Control via Alexa GoogleSONOFF NSPanel Pro is a smart home control panel. Your smart lights, switches, heaters, coolers, curtains and all your smart devices can be controlled. Unlimited number of control devices, all in one panel.NSPanel Pro can quickly add Zigbee devices to the screen in batches. The Zigbee 3.0 Standard protocol makes the connection more stable and the coverage wider. Supports all SONOFF Zigbee devices such as Zigbee, ZBMINI and BASICZBR3 sensors.NSPanel Pro can be used as a screen, supports adding the following four camera types for live monitoring. Visualization of real-time monitoring of living room, garage, bedroom, etc. on the panel at any time.Power consumption graph, custom wallpaper, and call intercom... it will update more features and HA support, matter in the future. NSPanel Pro will be your wonderful choice.Note: The case holder does not include NSPanel or NSPanel Pro. You must purchase each item separately.Better performance to meet your needsAll in One PanelUnlimited number of control devices, support control of all SONOFF devices, from smart lights, smart cameras, security to switches, etc., and will continue to support new SONOFF device in the future.One click to activate smart scenesUse with different smart devices, switch home scenes with just one click.Not only smart panel, but Zigbee HubQuickly add Zigbee devices to the screen in batches. The Zigbee 3.0 Standard protocol makes the connection more stable and the coverage wider. Added sub-devices can be voice controlled working with Alexa, Google Home, and more.Customize your Home Security ModeCustomize 3 modes by setting different arming devices. After arming, once the sensor is triggered, the panel will alarm, and you will get a notification alert on the phone.See real-time monitoring on the panelNSPanel Pro can be used as a screen, supports adding the following four camera types for live monitoring. You can view real-time monitoring of living room, garage, bedroom, etc. on the panel at any time.Remote Chat by CameraUsed with smart camera, when someone comes to visit, check the situation through the camera first to confirm safety. It also supports two-way communication to facilitate communication.Call intercom, Communication more convenientWith built-in microphone and speaker, it supports using mobile phone to call panel and panel-to-panel calls.Intelligent temperature control, make life easierChoose temperature source and runtime devices to form your own thermostat. Keep a suitable room temperature for you.Compatible with Home AssistantSupport two-way sync between NSPanel Pro and Home Assistant devices, you can sync Zigbee sub-devices from NSPanel Pro to HA, and sync lights and switches on HA to NSPanel Pro.Explore richer functions in wedding pagesListen to music, watch videos, or check out the latest tips? Register the address in NSPanel Pro web pages, quickly start it with one click, and relax at any time.Delicate Wallpaper for YouDifferent wallpapers for you to choose. Weather wallpapers that automatically switch based on the current weather? Or upload a photo to your phone as wallpaper? Set your own wallpaper style!Accompany you in daily lifeCheck power consumption at any timeYou can check the power consumption on the panel at any time. The smart panel to check energy consumption helps you live an eco-friendly life.Use as You LikeCompatible with case mount.
Digital Multimeter Koban KMD-23
MultimeterDigitalKoban KMD-23Digital multimeter with measurement category CATII 500V, 2000 resolution accounts and backlit display.It performs AC/DC voltage measurements, DC current, resistance and temperature.It has diode and continuity test and transistor test.
Female DC Power Connector
Female DC Power ConnectorSize:Inner diameter: 2.1mmOuter diameter: 5.5mmTransmission voltage: 5V-38VTransmitting power: 80WUsed for: led strip, CCTV camera, power supply, 3D printerCharacteristic:The wire core is thick and can withstand voltage from 12V to 36V,The outer skin is made of plastic and other materials, and the wire body is softHigh fidelity design, good power transmission effect
4 x 5MP Flexible Multi-sensor Network Camera
The Dahua 4 x 8MP Enhanced Starlight Multi-sensor Network Panoramic Bullet Camera provides added flexibility for capturing wide area video security. With four (4) 8MP sensors working in tandem to create a comprehensive 180° overview, the camera can replace multiple single-sensor cameras. The multi-sensor camera features contrast, backlight compensation, white balance, and resolution control to create clear images even in the most challenging lighting conditions. The camera is ready for any application with IP67 and IK10 ratings.
lead acid batterie 20hr 6v 4ah battery long
· Certification: CE· Certification: FCC· Origin: CN (Origin)· Application: Consumer Electronics, Electric Wheelchairs· Battery Size: 6v4ah· Model Number: a003· Weight: 730g · Keyword: 6v 4ah battery
Doorbell videophone 4-wire with RFID reader ENERGICAL VFE 01-C
FURTHER INFORMATION:Size: 18.8x12.5x6cmModel: 4-wire systemModel Number: VFE 01-CBrand: ENERGYCALNote: this model contains a 125KHZ RFID reader, you can use it as an access controller
Insulated Precision Screwdriver Set 7Pcs-1000V-Orange Tolsen 32007
7PCS INSULATED PRECISION SCREWDRIVER SET• 5pcs insulated precision slotted screwdrivers: 1.5×0.23x50mm, 1.8×0.30x50mm, 2.0×0.40x50mm, 2.5×0.40x50mm, 3.0×0.50x50mm• 2pcs insulated precision phillips screwdrivers: PH00x50mm, PH0x50mm;• VDE/GS certificated• S2 material blade, entirely hardened and tempered• Chemically blacked surface• Grip and sleeve manufactured according to EN60900• Ergonomic shape handle• Packing: color box
Overload relay Tense TRM-25
Characteristics:Controlled / measured valueoverloadOther characteristicsdigitalTripping currentMax: 25 AMin: 0.1 ADigital thermal relays are designed to prevent and control damage to loads caused by high current.0.1A - 25A (adjustable overload value)50% Fixed current asymmetryAdjustable delay time in case of errorAdjustable operating mode (automatic, semi-automatic, manual)Internal current transformers
AJAX HUB 2 PLUS Central alarm
AJAX HUB 2 PLUS Central alarm :The AJAX HUB2 PLUS alarm control panel, is a connected security system with alarms that allows you to control a variety of connected devices to protect your home.A wide range of accessories completes the AJAX HUB2+ control panel:Motion detectors (PIR CAM), opening detectors and even remote controls to start or stop the AJAX security system.The HUB2+ system can support up to 64 scenarios for various situations. So define a scenario for each of your living rooms and thus avoid the involuntary triggering of the AJAX security system.To accommodate these different scenarios, Hub 2 plus can control up to 200 devices, manage 25 security groups and up to 200 users.The system has tamper protection with a tamper alarm that activates if an intruder attempts to disassemble the device. In case of signal interference, a notification will be sent. In the event of a power outage, the built-in backup battery allows the system to operate for up to 15 hours.The system is also easy to install, scalable and regularly installs updates to its security system automatically.Strong points :Central alarm AJAX HUB 2 PLUSNotification in case of jamming of signals and transmissionsVandalism protectionIP50 certified: Protection against dustPhoto transmission delay: 9 secondsImage resolution: 640 x 480 pixelsPush notifications / calls / SMSAlarm reception delay: 0.15 secondsTechnical characteristics :Maximum number of connected devices: 100Maximum number of connected radio signal range extenders: 5Maximum number of cameras: 25Maximum number of users: 50Maximum number of coins: 50Maximum number of scenarios: 64Maximum number of security groups: 9Communication networks Hub 2 (4G): Ethernet / 2 SIM cards / LTESend photo after detectionSeries of 1 to 5 photosPhoto transmission delay: 9 secondsInstant switching between 2G, 3G, LTESwitching between SIM cards: 4 minutesSupported central station communication protocols: Sur-Gard (Contact ID), SIA (DC-09), proprietary protocols.Compatible Monitoring Software: PRO DesktopOperating system: OS MalevichPower supply: 100 - 240V, 50/60HzConsumption in 110-240 V: Up to 10 WBackup Battery: Li-Ion 2 Ah (Up to 16 hrs battery life when Ethernet is disabled)Jeweler radio protocolRadio protocol communication range: Up to 2,000 meters free fieldTwo-way communication between devicesPermissible humidity: Up to 75%
XVR DVR DAHUA 4-CHANNEL 1080P VIDEO RECORDER PENTA-BRID COOPER DH-XVR1B04-I
XVR DVR DAHUA 4-CHANNEL 1080P VIDEO RECORDER PENTA-BRID COOPER DH-XVR1B04-ISystemMain ProcessorEmbedded processorOperating SystemEmbedded linuxSMD PlusPerformance4 channelsAI SearchSearch by target classification (Human, Vehicle)Video and AudioAnalog Camera Input4 channels, BNCHDCVI Camera Input1080p@ 25/30 fps, 720p@25/30/50/60 fpsAHD Camera Input1080p@ 25/30 fps, 720p@ 25/30 fpsTVI Camera Input1080p@25/30 fps, 720p@25/30 fpsCVBS Camera InputPAL/NTSCIP Camera Input4+1 channels, each channel up to 2MPAudio In/Out1/1, RCATwo-way TalkReuse audio in/out, RCARecordingCompressionAI Coding/H.265+/H.265/H.264+/H.264Resolution1080N; 720p; 960H; D1; CIFRecord RateMain Stream:All channels 1080N/720P/960H/D1/CIF/(1~25/30fps)Sub stream:CIF (1~15 fps)Bit Rate32 kbps–4096 kbps per channelRecord ModeManual; Schedule (General, Continuous); MD (Videodetection: Motion Detection, Video Loss, Tampering);Alarm; StopRecord Interval1 min– 60 min (default: 60 min), Pre-record: 1 s–30 s, Post-record: 10 s–300 sAudio CompressionG.711A; G.711U; PCMAudio Sample Rate8 KHz, 16 bit per channelAudio Bit Rate64 kbps per channelDisplayInterface1 HDMI; 1 VGAResolution1920 × 1080, 1280 × 1024, 1280 × 720Multi-screen DisplayWhen IP extension mode not enabled: 1/4When IP extension mode enabled: 1/4/6OSDCamera title; Time; Video loss; Camera lock; Motion detection; RecordingNetworkInterface1 RJ-45 Port (100 Mbps)Network ProtocolHTTP; HTTPS; TCP/IP; IPv4/IPv6; 3G/4G; UPnP; RTSP; UDP; SMTP; NTP; DHCP; DNS; IP Filter; PPPoE; DDNS; FTP; Alarm Server; P2P; IP Search (Supports Dahua IP camera, DVR, NVS, etc.)Max. User Access128 usersSmart PhoneiPhone; iPad; AndroidInteroperabilityONVIF 16.12, CGI ConformantVideo Detection and AlarmTrigger EventsRecording, PTZ, Tour, Video Push, Email, FTP, Snapshot, Buzzer and Screen TipsVideo DetectionMotion Detection, MD Zones: 396 (22 × 18), Video Loss, Tampering and DiagnosisAlarm inputN/ARelay OutputN/APlayback and BackupPlayback1/4Search ModeTime/Date; Alarm; MD and Exact Search (accurate to second)Playback FunctionPlay; Pause; Stop; Rewind; Fast play; Slow Play; Next File; Previous File; Next Camera; Previous Camera; Full Screen; Repeat; Shuffle; Backup Selection; Digital ZoomBackup ModeUSB Device/NetworkStorageInternal HDD1 SATA port, up to 6 TB capacityeSATAN/AAuxiliary InterfaceUSB2 USB ports (USB 2.0)RS485N/ARS232N/AElectricalPower SupplyDC 12 V/1.5 APower Consumption(Without HDD)< 7="" />ConstructionDimensionsCooper 1U, 198 mm × 202.9 mm × 41.5 mm(7.81'' × 7.99'' × 1.63'')Net Weight(without HDD)0.57 kg (1.25 lb)Gross Weight1.08 kg (2.38 lb)InstallationDesktop installationEnvironmentalOperating Conditions–10 °C to +45 °C (+14 °F to +113 °F), 0%–90% (RH)Storage Conditions–20 °C to +70 °C (–4 °F to +158 °F), 0%–90% (RH)Third-party SupportThird-party SupportDahua, Arecont Vision, AXIS, Bosch, Brickcom, Canon, CP Plus, Dynacolor, Honeywell, Panasonic, Pelco, Samsung, Sanyo, Sony, Videotec, Vivotek, and moreCertificationsCertificationsFCC: Part 15 Subpart BCE: CE-LVD: EN 60950-1/IEC 60950-1CE-EMC: EN 61000-3-2; EN 61000-3-3; EN 55032; EN 50130; EN 55024
AJAX MotionCam White - Motion Detector with a Photo Camera to Verify Alarms
AJAX MotionCam White - Motion Detector with a Photo Camera to Verify AlarmsMotion detector with a photo camera to verify alarmsTransmits a photograph in under 9 secSees in the darkOperates on a distance of up to 1700 m from the hubPhoto capture only when alarmedAll pictures are encryptedIgnores pets weighing up to 20 kg and growing up to 50 cmMotionCam detectors require Hub 2 or Hub 2 Plus for operationOperates up to 4 years on the pre-installed batteriesReveals what’s happeningWith the MotionCam, you see what triggered an alarm. The detector spots people’s motion within a 12-meter range and takes a series of photos.In contrast with the video surveillance systems, MotionCam wireless detectors take minutes to install, are independent of Wi-Fi, and continue to operate smoothly even during a blackout.ClassificationElectro-optical combined radio channel security detector with a photo cameraDetector typeWirelessInstallationIndoorsMotion detection distanceUp to 12 mPet immunity Weight: up to 20 kgHeight: up to 50 cmCompatibilityOnly with Hub 2 or Hub 2 PlusSensing elementPIR sensorDetection angles Horizontal — 88.5°Vertical — 80°Camera view angle90°Alarm signal delivery time0.15 secPhoto verification Time to deliver a photograph with default settings: up to 9 secPhoto quality: up to 640 × 480 pxPictures in a series: 1-5 pcsIR backlight fornight mode picturesAvailableSensitivityAdjustable, 3 levelsRecommendedinstallation height2.4 mPower supplyBatteries: CR123A (x2), 3 VJeweller radio technology Communication range with detectors: up to 1,700 m in the line of sightTwo-way communication between devicesOperating frequencies: 868.0 - 868.6 MHzSelf-adjusting RF output power: up to 20 mWBlock encryption based on AES algorithmDetector polling period: 12−300 sFrequency hoppingWings radio technologyTransmission of visual alarm verificationsTemperature sensorAvailableOperatingtemperature rangeFrom -10°C to +40°COperating humidityUp to 75%
SONOFF nspanel Pro connected home control panel
SONOFF NSPanel Pro Smart Home Control Panel EU HMI TFT 3.95" Touch Screen Smart Scene Display Voice Control via Alexa GoogleSONOFF NSPanel Pro is a smart home control panel. Your smart lights, switches, heaters, coolers, curtains and all your smart devices can be controlled. Unlimited number of control devices, all in one panel.NSPanel Pro can quickly add Zigbee devices to the screen in batches. The Zigbee 3.0 Standard protocol makes the connection more stable and the coverage wider. Supports all SONOFF Zigbee devices such as Zigbee, ZBMINI and BASICZBR3 sensors.NSPanel Pro can be used as a screen, supports adding the following four camera types for live monitoring. Visualization of real-time monitoring of living room, garage, bedroom, etc. on the panel at any time.Power consumption graph, custom wallpaper, and call intercom... it will update more features and HA support, matter in the future. NSPanel Pro will be your wonderful choice.Note: The case holder does not include NSPanel or NSPanel Pro. You must purchase each item separately.Better performance to meet your needsAll in One PanelUnlimited number of control devices, support control of all SONOFF devices, from smart lights, smart cameras, security to switches, etc., and will continue to support new SONOFF device in the future.One click to activate smart scenesUse with different smart devices, switch home scenes with just one click.Not only smart panel, but Zigbee HubQuickly add Zigbee devices to the screen in batches. The Zigbee 3.0 Standard protocol makes the connection more stable and the coverage wider. Added sub-devices can be voice controlled working with Alexa, Google Home, and more.Customize your Home Security ModeCustomize 3 modes by setting different arming devices. After arming, once the sensor is triggered, the panel will alarm, and you will get a notification alert on the phone.See real-time monitoring on the panelNSPanel Pro can be used as a screen, supports adding the following four camera types for live monitoring. You can view real-time monitoring of living room, garage, bedroom, etc. on the panel at any time.Remote Chat by CameraUsed with smart camera, when someone comes to visit, check the situation through the camera first to confirm safety. It also supports two-way communication to facilitate communication.Call intercom, Communication more convenientWith built-in microphone and speaker, it supports using mobile phone to call panel and panel-to-panel calls.Intelligent temperature control, make life easierChoose temperature source and runtime devices to form your own thermostat. Keep a suitable room temperature for you.Compatible with Home AssistantSupport two-way sync between NSPanel Pro and Home Assistant devices, you can sync Zigbee sub-devices from NSPanel Pro to HA, and sync lights and switches on HA to NSPanel Pro.Explore richer functions in wedding pagesListen to music, watch videos, or check out the latest tips? Register the address in NSPanel Pro web pages, quickly start it with one click, and relax at any time.Delicate Wallpaper for YouDifferent wallpapers for you to choose. Weather wallpapers that automatically switch based on the current weather? Or upload a photo to your phone as wallpaper? Set your own wallpaper style!Accompany you in daily lifeCheck power consumption at any timeYou can check the power consumption on the panel at any time. The smart panel to check energy consumption helps you live an eco-friendly life.Use as You LikeCompatible with case mount.
Temperature sensor probe NTC 10K -40-120C used in temperature controller
1m NTC 10K temperature sensor probe -40-120C cylinder-shaped 4*25mm used in temperature controllerTechnical parameters: NTC 10K B = 3435 +-1% accuracyMaterial: anti-embroidered cylindrical nickel-plated copperProduct Specifications: diameter 4MM * Length 25MmWire specifications: about 1 meter, 2 meters, 5 meters cable, please choose the one you need.Applications: suitable for temperature -40 C ~ 120 C Applicable areas: Sensor very repid , accurate ! but its waterproof performance is very common. it is often used in refrigerators, air conditioners, fans, mist or larger air temperature and humidity, do not recommend long-term immersion in water.
Phase Sequence Phase Failure Voltage Analogue Adjustable Protection Relay (With Neutral Wire)
General Voltage Controller Relays are designed to avoid the failures of network voltage for the devices which have sensitive working voltage.Usage and Working Principle Make the connections according to the diagram. Set the device according to the required electrical charge. When the power is on, if the voltages are same as adjusted, relay led switches on and relay pulls. In this cases contact out is(NO)3 pole. When the volage values are avnormal, relay releases and led is switched off after waiting till the setted time is up. In this case contact out is (NC)1. GK-04FN type voltage controller relay doesn't work if the phase sequence is incorrect.MaintenanceSwitch off the device and release from connections. Clean the trunk of device with a swab. Don't use any conductor or chemical might damage the device. Make sure device works after cleaning.WarningsPlease use the device according to the manual. Don’t use the device in wet. Include a switch and circuit breaker in the assembly. Put the switch and circuit breaker nearby the device, operator can reach easily. Mark the switch and circuit breaker as releasing connection for device.SpecificationsOperating Voltage(Un)....: 3 x 380V AC + Neutral Operating Frequency.......: 50/60 Hz. High Voltage (U>)...........: 400V - 460V Low Voltage (U
Internal hard drive for Western Digital video surveillance - WD Purple 1TB
Internal hard drive for Western Digital video surveillance - WD Purple 1TBDescription of hard drive Mechanical hard driveCompatible devices : OfficeColor : OthersHard drive size :1000 GBHard drive rotation speed : 5400 rpmDigital storage capacity : 1 TBSerial ATA 600 hard drive interfaceSATA connectivity technologyBrand : Western Digital3.5 inch hard drive form factorDescription of hard drive : Mechanical hard drive
Ajax AJ-door wireless magnetic opening detector
Ajax AJ-door wireless magnetic opening detectorWireless opening detector that signals the first signs of intrusion into the room by breaking into a door or window. It can be mounted on all types of doors, including on a metal base.Authentication against fraudJamming detection and encryption of communication channelsAnti sabotage alarmsecurity levelThe device can operate for 7 years without replacing the batteries.An external contact is available for the connection of third-party detectors.Includes magnets of different sizes for installation on narrow frames and door frames.Principle of operationThe device detects the door or window that is opened using high-end British Reed relay contactor on which the magnetic field acts. It can operate in transmitter mode, sending a signal from the wired sensor to the Hub.FunctionsThe device consists of two modules - detector and magnet. The set includes two magnets: the large magnet is installed at a distance of up to 2 cm, and the small magnet at a maximum of 1 cm.Installation and commissioningReady to work right out of the box: the battery is already installed, so there is no need to disassemble the detector. With a single click, it can be connected to the Hub in the mobile app. It can be mounted on the SmartBracket in just a few minutes.Technical specificationsClassificationSafety detector with radio channel and magnetic contact pointDetector Type: WirelessInstallation method: IndoorSensor element: Reed contactorAlarm signal reception delay: 0.15sActivation thresholdSmall magnet — 1 cmLarge magnet — 2 cmFeedBattery: CR123A batterySupply voltage: 3 VBattery life – up to 7 yearsJeweler wireless technologyCommunication range with the central unit – up to 1200 m in open spaceTwo-way communication between devicesOperating frequencies – 868.0 – 868.6 MHzSelf-adjusting RF output power – up to 20 mWData packet encryption based on the AES algorithmDetector polling period – 12 – 300 sTemperature sensor: AvailableOperating temperature range: -10°С to +40°СPermissible humidity: Up to 75%Storage temperature range: +5°С to +40°СAnti-tamperTamper protectionJamming detectionInviolableRemote adjustment and test+DimensionsDiameter: 20mmHeight: 90mmWeight: 29gCertification: Grade 2, CE
TOLSEN V83306 1000V 6PCS Insulator Screwdriver and Pliers Set
Tolsen V83306 plier set is manufactured from chrome vanadium steel with toughened cutting edges1pc 180mm insulated combination plier1pc 160mm insulated diagonal cutting plier2pcs insulated slotted screwdriver: 0.4×2.5x75mm, 0.8×4.0x100mm1pc insulated phillips screwdriver: PH2x100mm1pc 3.0x70mm voltage testerVDE/GS certificatedManufactured according to EN60900Packed by canvas bag with color boxPacking: canvas bag with color box
Tolsen V33212-12pcs Insulated Changeable Screwdriver Set - VDE 1000 Volts
Tolsen V33212-12pcs Insulated Changeable Screwdriver Set - VDE 1000 VoltsKit with 11 insulated screwdrivers and removable handle,Steel type S2, manufacturing according to standard EN60900, VDE GS certification.Composed of 5 flat screwdrivers: 0.4x2.0x100mm; 0.4x2.5x100mm; 0.5x3.0x100mm; 0.6x3.5x100mm; 0.8x4.0x100mm; 1.0x5.5x100mm; 1.2x6.5x100mm;3 Phillips type screwdrivers: PH0x100mm, PH1x100mm and PH2x100mm.Universal handleMatte black dipped finish. Very compact and practicalCAUTION: Always wear suitable protective equipment: gloves, mask, overalls.The standards used and the notice are suitable for professional use or informed general public, with the only restriction that the public in question is:- Expert / competent person / qualified person: person who can judge the assigned work and recognize possible dangers on the basis of his professional training, his knowledge, his experience and his knowledge of the material concerned- informed person: person informed of the assigned tasks and the possible dangers due to negligenceThe obligation to read the instruction manual before use and the content of the instruction manual make it possible to inform the user about the possible stains and the possible dangers due to negligence,
COB Super Bright LED Mini Flashlight USB Rechargeable Waterproof Camping Lantern Zoomable Torch
Features:*Eco-friendly COB lamp beads, long life and high brightness with energy efficiency.*Come with high quality lanyard on the bottom for easy hanging and carry.*3 lighting modes for free switch as desire with simple pressing button operation.*Mini rechargeable battery with USB charging cable to provide continuous illumination.*2-in-1 mini flashlight &LED work light with high brightness, suitable for cycling, hiking, camping and other outdoor activities.Specifications:Material: Aluminium AlloyBattery: Inside Rechargeable BatteryBead Type: COBPower Supply: USB ChargingLength: 9.3cmLamp Holder Diameter: 2.7cmTail Cover Diameter: 2.1cmPackage Included:1*USB Cable1*COB Work Light Flashlight
VOLTAGE DETECTOR (V.A.T) BT IP2X FAMECA TAG780
Voltage detector (VAT) Low Voltage IP2X TAG780To perform voltage absence checks on low voltage networks as part of lockout operationsSticks can be mounted on the device to carry out voltage absence checks on overhead networksFEATURES• Compliance with IEC 61243-3 standard• Voltage range: 12 to 1000 V DC and AC (15 to 60 Hz).• Audible voltage presence alarm differentiated according to the voltage level (discontinuous sound up to the 230 V level and continuous sound beyond the 400 V level).• Polarity display (-/+).• Integrated self-test.• Continuity check (threshold 80Ω).• Phase search in unipolar mode (indifferent use of one or the other of the test probes).• Lighting on the front face.• Protected against water and dust: IP65.• Protected against overvoltages. CATIV 1000V.• Supplied with 2 AAA batteries and carrying bag.MORE PRODUCT:• New generation, ultra-bright display.• Reading possible even in bright light.• Double insulated silicone cord: robust and ultra flexible (no memory effect).• Display up to 1000 V.• Retraction of the sheath by a trigger on the back of the device (exclusive solution guaranteeing control of sheath withdrawal and visual safety on contact)• Control point lighting diode• Possibility of mounting poles on the device to check the absence of voltage on overhead networks (ref. SFEANT780)
TENSE GKT-03F analog adjustable phase sequence three-phase overvoltage and undervoltage control relay
TENSE GKT-03F analog adjustable phase sequence three-phase overvoltage and undervoltage control relayDESCRIPTION :Voltage monitoring relays are designed to protect sensitive operating voltage devices from damage caused by mains voltage. Surge: 400V - 510V AC (adjustable) (can be disabled)Under voltage: 260V - 370V AC (adjustable) (can be disabled)Error wait time: 0.1sec. - 20 sec. (adjustable)Reset time: 0.1sec. - 20 sec. (adjustable)Phase sequence controlNot neutralFEATURES :Measured value: overvoltage, undervoltage, phase orderMounting: on DIN railOther features: adjustableTrigger Voltage: Max: 510V Min: 260V
Deal Of The Day
DAHUA 16-CHANNEL 1080P DVR (XVR) VIDEO RECORDER PENTA-BRID COOPER DH-XVR1B16-I
DAHUA 16-CHANNEL 1080P DVR (XVR) VIDEO RECORDER PENTA-BRID COOPER DH-XVR1B16-I>H.265 +/H.265 dual-stream video compression>Supports full-channel AI coding>Supports HDCVI/AHD/TVI/CVBS/IP video input>Maximum 18 channel IP camera inputs, each channel up to 6MP; Maximum incoming bandwidth of 64 Mbps>Long transmission distance on coaxial cable>Up to 16 video stream channels (analog channel) SMD PlusSystem Main processor Industrial grade processorOperating system Embedded LinuxOperating interface Web; Local GUISMD PlusSMD Plus per Recorder 8 channels: secondary filtering for human and automobile vehicles, reducing false alarms caused by leaves, rain and lighting status changes Audio and Video Analog Camera Input 4/8/16 channels, BNC: adaptive access by default; HDCVI, AHD, TVI and CVBS access can be configured. Camera Input 1. CVI: 1080p @ 25/30 fps, 720p @ 25/30 fps2. TVI: 1080p @ 25/30 fps, 720p @ 25/30 fps3. AHD: 1080p @ 25/30 fps, 720p @ 25/30 fps4.CVBS:PAL/NTSC IP Camera Input Up to 18 IPC access channels Default 2 IP channels + 16 channels (analog channels are converted to IP channels) Incoming bandwidth: 64 Mbps, recording bandwidth: 64 Mbps and outgoing bandwidth: 64 Mbps * Once IP channels are added beyond the existing channels, the AI (SMD) function will be disabled. Encoding capacity Main current:The 1st channel 1080N/720p (1 fps-25/30 fps), others1080N/720p (1fps-15fps); 960H/D1/CIF(1fps-25/30fps)Under flow:Cif (1 fps-7 fps) Dual-flowYes Video Little Rate32kbps-6144kbps Audio Sampling8 kHz, 16 bit Audio Low Rate64 kbps Video Output 1 HDMI, 1 VGAHDMI/VGA: 1920 × 1080, 1280 × 1024, 1280 × 720 Multi-screen Display1/4/8/9/16 Third-party camera accessONVIF; RTSP; Panasonic; Sony; Axis; Arecont; Pelco; Cannon; Samsung Compression StandardCompression Video AI coding; H.265+; H.265; H.264+; H.264 Audio CompressionG.711a; G.711u; PCM Network Network protocol HTTP; HTTPS; TCP/IP; IPv4; RTSP; UDP; SMTP; NTP; DHCP; DNS; DDNS; P2P Mobile Phone Access IOS, Android Interoperability ONVIF 21.06; CGI Compliant Navigator ChromiumIE9 or laterFirefox Network mode Uniue-address mode Recording Playback Recording modeGeneral, motion detection, alarm; Recording Playback1/4/9/16 Backup methodUSB and network device Reading mode Instant read, general read, event read, tag readAlarm General AlarmMotion detection, video loss, alterationAnomaly AlarmNo Disk, Disk Error, Low Space, Offline, IP Conflict, MAC Conflict Alarm linkage Recording, snapshot (panning), IPC external alarm output, access controller, voice prompt, buzzer, log, preset, email Ports Audio Input 1-channel RCA16 channel BNC (Coaxial Audio) Audio Output 1-channel RCA Two-way ChatYes (share the same audio input with the first channel) HDD interface 1 SATA port, up to 16TB. The maximum hard drive capacity varies depending on the ambient temperature. USB2 USB ports (USB 2.0) HDMI1 VGA1 Network Port1 (10/100 Mbps Ethernet port, RJ-45) General Food12 VDC, 2 A Energy consumption
AJAX MotionCam White - Motion Detector with a Photo Camera to Verify Alarms
AJAX MotionCam White - Motion Detector with a Photo Camera to Verify AlarmsMotion detector with a photo camera to verify alarmsTransmits a photograph in under 9 secSees in the darkOperates on a distance of up to 1700 m from the hubPhoto capture only when alarmedAll pictures are encryptedIgnores pets weighing up to 20 kg and growing up to 50 cmMotionCam detectors require Hub 2 or Hub 2 Plus for operationOperates up to 4 years on the pre-installed batteriesReveals what’s happeningWith the MotionCam, you see what triggered an alarm. The detector spots people’s motion within a 12-meter range and takes a series of photos.In contrast with the video surveillance systems, MotionCam wireless detectors take minutes to install, are independent of Wi-Fi, and continue to operate smoothly even during a blackout.ClassificationElectro-optical combined radio channel security detector with a photo cameraDetector typeWirelessInstallationIndoorsMotion detection distanceUp to 12 mPet immunity Weight: up to 20 kgHeight: up to 50 cmCompatibilityOnly with Hub 2 or Hub 2 PlusSensing elementPIR sensorDetection angles Horizontal — 88.5°Vertical — 80°Camera view angle90°Alarm signal delivery time0.15 secPhoto verification Time to deliver a photograph with default settings: up to 9 secPhoto quality: up to 640 × 480 pxPictures in a series: 1-5 pcsIR backlight fornight mode picturesAvailableSensitivityAdjustable, 3 levelsRecommendedinstallation height2.4 mPower supplyBatteries: CR123A (x2), 3 VJeweller radio technology Communication range with detectors: up to 1,700 m in the line of sightTwo-way communication between devicesOperating frequencies: 868.0 - 868.6 MHzSelf-adjusting RF output power: up to 20 mWBlock encryption based on AES algorithmDetector polling period: 12−300 sFrequency hoppingWings radio technologyTransmission of visual alarm verificationsTemperature sensorAvailableOperatingtemperature rangeFrom -10°C to +40°COperating humidityUp to 75%
Multi Port 8 Channel CCTV SMPS Power Supply (Input 150-300V, Output 12 Volt 10 Amp)
Specifications :Manual Switch for normal, long , extra-long cable distance. Cable compensation switch for voltage boostingStabilized Output & Low Interference. Short Circuit & Overload Protection Thermal ProtectionPower LED Indicator for Individual Channel. Low Ripple Voltage. Short Circuit Auto Restart. Highly Integrated SMPS Switcher I.C. DesignSurge Protection/Lightning Proof. Over Temperature & Voltage Protection. High Efficiency & Low Energy Consumption.12V 10 Amp. Heavy Industrial QualityInput : 150-285 VAC 47-63HzOutput : 12V/12.5V/15V ( selected by switch ) Max 1A/channel Frequently Asked Question(FAQ)1. Can use for analogue HD cameras ? – Yes, It use for analogue old technology like 420 TVL, 480 TVL, 520 TVL, 600TVL, 720TVL, 800TVL, 900TVL & 1000TVL and HD analogue cameras like 1mp, 1.3mp, 2mp, 3mp, 4mp & 5mp Camera.2. Can use SMPS for outdoor cameras ? – Yes, can use for both indoor and outdoor camera.3. Till how many meters of CCTV camera can use power supply ? – It can use upto 90m cable distance between CCTV camera and DVR(Recorder) in Ex-Long mode.4. CCTV power supply have 3 modes ? Yes,(a) Normal, (b) Long & (c) Ex-Long modes are available.Usage of modes are upto 60m-normal mode, upto 75m-Long mode and upto 90m-Ex-Long mode.5. Camera power supply is weather proof ? – No, CCTV SMPS placed inside closed space where can protect from external weathers.6. Can use for IP camera ? –Yes, it can use for IP cameras.
A9 video surveillance wifi camera camera 1080 HD
A9 wifi camera1080P HD IP Mini Camera Wireless Recorder Security Remote Night Vision Mobile Detection surveillance cameraProduct details:APP platform: HDWiFiCamPro video format: AVI video resolution: 1080P Night vision: 0.5Lux frame rate: 25fps Viewing angle: 150 degree motion detection camera distance: 6 meters straight battery working time: 1 hour compressed format : H.264 recording range: 5 square meters storage capacity: up to 128G Support system: Android / IOS power consumption: 240MA / 3.7V playback software: VLCP layer / SMP layer motion detection : Support interface: Micro 5PIN USB charging voltage: DC-5V size: 4.5 * 4 * 2CMPackage:1 * camera1 * bracket1 * USB cable1 * snake pipeline · Type: ip camera· Supported Operating Systems: windows xp· High Definition: 1080P(Full-HD)· Lens (mm): 3.7mm· Style: Mini Camera· Certification: KC· Connectivity: WIFI· Smart home platform: Other· Origin: CN(Origin)· Installation: Normal· Wall Bracket: Ceiling· Power Consumption(W): 10w· Color: black· Minimum Illumination(Lux): 10A· Sensor: CMOS· Megapixels: 2MP· Sensor Brand: SONY· Special Features: Vandal-proof· Storage: None· Alarm Action: Local Alarm· Video Compression Format: MPEG4· Power Supply: Normal· TF Card: None· IR Distance(m): 12m· is_customized: Yes· Model Number: A9· Viewing Angle : 130°· Technology: Infrared· Supported Mobile Systems: Android· Network Interface: Wi-Fi/802.11/b/g
CCTV power supply box 18 channel DC12V 20A 240W
18 channel DC12V 20A CCTV Camera Power Box CCTV PTC Distributed switching Power Supply Box for Security Video Camera 18CHs PortSpecification:OUTPUT DC Port:18 ChannelOUTPUT VOLTAGE:DC 12VRATED CURRENT:DC 20ARATED POWER:240WSupport to:18PCS CamerasINPUT VOLTAGE RANGE:AC 100-120V, AC 200-240V, 50Hz / 60HzFREQUENCY RANGE:47-63HZLEAKAGE CURRENT:1mA/240VACENVIRONMENT:WORKING TEMP -10~+60°CWORKING HUMIDITY:20-90%RH non-condensingSTORAGE TEMP,HUMIDITY:-20~+85°C,10-95%RHShell Material:Metal case / Aluminum caseDIMENSION:315X220X60 mmPACKING:2.82kg, 10pcs/27kgPackage Content:1*18CH 12V/20A Power Box
DC Male Power Connector
DC Male Power ConnectorrSize:Inner diameter: 2.1mmOuter diameter: 5.5mmTransmission voltage: 5V-38VTransmitting power: 80WUsed for: led strip, CCTV camera, power supply, 3D printerCharacteristic:The wire core is thick and can withstand voltage from 12V to 36V,The outer skin is made of plastic and other materials, and the wire body is softHigh fidelity design, good power transmission effect
Digital Multimeter Koban KMD-23
MultimeterDigitalKoban KMD-23Digital multimeter with measurement category CATII 500V, 2000 resolution accounts and backlit display.It performs AC/DC voltage measurements, DC current, resistance and temperature.It has diode and continuity test and transistor test.
Access Control Touch Keypad and IP Video Door Phone Waterproof with Fingerprint Tuya Compatible
Access Control Touch Keypad and IP Video Door Phone Waterproof with Fingerprint Tuya CompatibleWIFI Video Intercom Access Intercom > 2.4G WiFi connection, > Android and iOS available > Full duplex voice intercom > 2MP+wide angle camera and night vision > Support TF card with unlimited capacity > Support motion detection, playback, take picture/video, unlock remotely Access Control > Touch key with one relay, 1000 users (988 common+2 panic+10 visitor) > PIN Length: 4~6 digits > EM card, Mifare card optional > Wiegand 26~44 bits in put & output > Can be used as Wiegand reader with LED & buzzer > User data can be transferred > 2 devices can be interlocked for 2 doors ideo IntercomNetwork2.4G WiFi connectionPixel2.0Mpx (1080P)Visual AngleHorizontal 140° wide angleNight VisionIR-CUT (Colorful at daytime, black and white at night)Extended MemoryTF card with unlimited capacityIntercomFull duplex voice intercomOther FunctionsMotion detection; Playback; Take picture/video; Unlock remotelyAccess ControlUser CapacityCommon UserVisitor UserPanic User1000(100 fingerprints + 900 card&PINs)98810 2PIN Length4~6 digitsProximity Card ReaderRadio TechnlogyRead RangeEM or Mifare125KHz/13.56MHz 2~6cmWiring ConnectionsRelay output, exit button, alarm, door contact, Wiegand input/outputRelayAdjustable Relay Output TimeLock Output LoadOne (NO, NC, Common)0~99 Seconds (5 seconds default)2 Amp MaximumWiegand Interface PIN OutputEM card version: Wiegand 26~44 bits input & output (Factory default: Wiegand 26bits)Mifare card version:Wiegand 26~44 bits input & output (Factory default: Wiegand 34bits)4 bits,8bits (ASCII),10 digits Virtual Number(Factory default:4bits)ElectricOperating VoltageIdle CurrentActive CurrentDC 12V≤ 150mA≤ 250mAEnvironmentOperating TemperatureOperating HumidityOutdoor (IP65)-20°C ~ 60°C (-4°F ~ 140°F)0%RH ~ 96%RHPhysicalColorDimensionsUnit WeightShipping WeightZinc-AlloySliver & BlackL147 x W56 x H26 (mm)470g570g
Xiaomi Mi Router 4A Wireless WiFi 2.4GHz 5.0GHz Dual Band 1167Mbps WiFi Repeater 4 Antennas Through-wall Network Extender
SpecificationsDimensions:188 mm x 100.5 mm x 175 mmProduct color:WhiteProcessor: MT7628DAInternal memory:64MB2.4G Wi-Fi2x2: (supports the IEEE 802.11n protocol, maximum possible speed of 300Mbp5G Wi-Fi2x2: (supports the IEEE 802.11ac protocol, maximum possible speed of 867Mbps)Product antennas:4 external omnidirectional antennas (two 2.4GHz antennas with maximum gain of 5dBi; two 5GHz antennas with maximum gain of 6dBi)Product heat dissipation:Natural heat dissipationTotal interfaces:Two 10/100M self-adaptive LAN ports (Auto MDI/MDIX)One 10/100M self-adaptive WAN port (Auto MDI/MDIX)LED indicator lights:2System reset buttons:1Power input interface:1Protocol standards:IEEE 802.11a/b/g/n/ac, IEEE 802.3/3uCertification standards:GB9254-2008, YD/T993-1998, GB4943.1-2011Wireless specificationsDual band:2.4GHz and 5GHzModulation11b: DSSS: DBPSK (1Mbps), DQPSK (2Mbps), CCK (5.5/11Mbps)11a/g: OFDM: BPSK (6/9Mbps), QPSK (12/18Mbps), 16QAM (24/36Mbps),64QAM (48/54Mbps)11n: MIMO-OFDM: BPSK, QPSK, 16QAM, 64QAM. Rate set: MCS0 to MCS1511ac: MIMO-OFDM: BPSK, QPSK, 16QAM, 64QAM, 256QAM. Rate set: MCS0 to MCS9 (supports 2 streams)SoftwarespecificationsOperating system:Mi Wi-Fi ROM intelligent router operating system based on a highly customized version of OpenWRTWireless security:WPA-PSK/WPA-PSK2 encryption, wireless access control (blacklist and whitelist), SSID hiding, smart unauthorized access preventionManagement application:Supports web, iOS, and AndroidProductaccessories1 x user manual 1 x product power supply (12V/0.6A)OperatingenvironmentOperating temperature:0–40°COperating humidity:10%–90% RH (no condensation)Storage temperature :-40–70°CStorage humidity:5%–90% RH (no condensation)Router Setup StepsSupport PC setting and APP setting, And you can change the settings page to the language of your countryPC settings: Please download Google Chrome in advance, and then open http://192.168.31.1/, this is the official setting webpage of Xiaomi router, you can translate it into your country’s language through Google Chrome, such as: English, Russian , Spanish, etc., just follow the prompts to set. TookfunAPP setting: Please download the Xiaomi WiFi app in advance1. Search and download the APP “Mi Wi-Fi” on Google Play or App Store.2. Powering the router, and open the WiFi (on the phone) to connect the Xiaomi Router3. 1) Create a Mi account then sign in your account;2) Follow the promotes to operation, click ”Dial-up access "to input your network account and the password; (The router supports PPPOE protocol)3) Click “More Options”, finish the primary base station (set up a new network name and password).4. Open the APP, complete your WiFi setting.
Repair tools flexible shaft extension with accessories BKGJ-001-L
Repair tools flexible shaft extension with accessories BKGJ-001-LName: Ratchet Screwdriver Combination Kit-Two-way rotation, free conversion,- Alloy steel tool shank, good torsion hardness.-The batch head is made of chrome-vanadium steel with high hardness.-Package includes:1 Piece Lengthening RodSet of screws 10 pieces:3 Flat Screwdriver Heads: 4-5-62 cruciform heads +: PH0, PH12 cruciform heads *: PZ1, PZ22 TORX head (star): T15, T201 AD Hexagonal head